IC Knowledge Base

Cables and Wiring

 

Cables Cabling RJ45 RJ21 MSAN

We use 568B for almost everything ethernet


Standard networking connectors for Ethernet connections. Rumor has it that only the “A” standard is accepted for government work and the “B” standard is being depreciated.

 

 


Power over Ethernet pinouts. More and more commonly used in VOIP phone systems, but can also be found in wireless access points and other things of that nature.

 

 


Ethernet crossover cables are useful for connecting to similar pieces of equipment together, e.g. a computer to a computer, or a switch to a switch. Many new switches have port sensing, which will automatically cross the connection if a straight through cable is used. Others have a specific port or a switch for a specific port which will cross over the cable. Gigabit Ethernet uses all four pairs, thus a 1000 base T crossover looks a little bit different.

 

 

 

 

 


This type cable is backwards compatible with 10/100 base T systems.

 

 


Telephone system equipment jacks.


RJ48 and 48X used on T-1 (DS-1) and ISDN connections. Since BRI and PRI ISDN are two wire circuits, the active pins are 4/5, which is the same as an RJ11. I have often used RJ11 jacks for ISDN and found no issues with doing so.

Crossover cable for T-1 (DS-1 or DSX-1 interface). Note, this is different from an Ethernet crossover cable, which will not work for in a DS-1 interface. A T-1 loopback connector goes from pin 1 to pin 4 and pin 2 to pin 5 on a 8P8C connector.

 

RJ21 and 21X connectors are often found on the side of punch blocks and make for quick connections on cabling trunks.


The generic 25 pair color code, which is always a good thing to have.

RS-232 is still commonly used for data transfer in broadcast facilities. RS-485 is also used, however, that standard is often used with screw terminals or some other generic connection.

 

Null modems for connecting equipment together and testing.

Various USB connectors and pinouts. USB has replaced RS-232 data ports on most newer computers.

Computer graphics card pinouts.

Computer parallel port pinout, not used very much anymore, replace by mostly USB devices. Can also be used as a limited GPI/GPO interface. Some small automation software programs use pins 10,11,12,13 and 15 for closure information and pins 1, 14, 16, and 17 for output switching, machine starts and the like.

PS2 mouse and keyboard connectors, again, replaced by USB but still found on older motherboards.

 

Power Cable Wiring

UK 13A, Kettle (c13/14) and Squareish (c19/20) type connectors are usually unlabelled and swapping the live and neutral can leave devices live when they are off so it is important to get it right.

 

5 (1)
Article Rating (1 Votes)
Rate this article
Attached Files
There are no attachments for this article.
Comments
There are no comments for this article. Be the first to post a comment.
Name
Email
Security Code Security Code
Related Articles RSS Feed
DNS Records
Viewed 2483 times since Wed, Aug 16, 2017
I can’t connect to the Internet
Viewed 3127 times since Thu, Jul 27, 2017
Riello UPS Error Codes
Viewed 28463 times since Mon, Jan 25, 2021
OSPF Routing Cost
Viewed 5986 times since Tue, Jul 25, 2017
10 Day Training Period
Viewed 3106 times since Wed, Jul 26, 2017
Slow Speed Broadband
Viewed 3658 times since Wed, Jul 26, 2017
Modems Vs Routers
Viewed 3500 times since Tue, Aug 22, 2017
Intermittent Broadband Connection
Viewed 3537 times since Wed, Jul 26, 2017
BT Terminology
Viewed 29921 times since Fri, Jul 21, 2017
DHCP
Viewed 3040 times since Wed, Aug 2, 2017
Internet Central Limited, Innovation Centre 2, Keele Science Park, Keele, Staffordshire ST5 5NH
Registered Office: Ivy House Foundry, Hanley, Stoke-on-Trent, ST1 3NR
Registered in England: Reg No. 03079542 VAT Reg No. GB 278 923 705
Contact Us |Terms & Conditions |Legal, Privacy and Cookies
All prices exclude VAT E.&O.E © 2015 Internet Central

All trademarks and logos appearing on the site are the property of their respective owners